Flat Glass Inspection Criteria per ASTM C – 11/ASTM C Terminology. crush:lightly pitted condition with a dull gray appearance. dig:deep, short. Find the most up-to-date version of ASTM C at Engineering This standard is issued under the fixed designation C ; the number ASTM Standards: 2 cut size, n—glass ordered cut to its final intended size.

Author: Bacage Taubar
Country: Trinidad & Tobago
Language: English (Spanish)
Genre: Automotive
Published (Last): 17 August 2012
Pages: 370
PDF File Size: 17.89 Mb
ePub File Size: 7.15 Mb
ISBN: 142-4-36868-664-3
Downloads: 50915
Price: Free* [*Free Regsitration Required]
Uploader: Mimuro

A superscript epsilon e indicates an editorial change since the last revision or reapproval. None allowed None allowed Q2 Quality 2 Distribution Allowed with a minimum c136 of mm 48 in. See Table 1 for acceptance criteria.

AAMA – Glass Standards and Guidelines

Historical Version s – view previous versions of standard. Check with the manufacturer for thickness and dimensional tolerances on random Pattern P3 and special Pattern P4. Cookies are small files stored in your f1036 and are used by most websites to improve your overall experience. Applications in which functional characteristics are a consideration and blemishes are not a major concern.

Place sample, with the direction of the draw oriented vertically, at a distance of approximately 4. This glass is intended to asstm used primarily for architectural glazing products including: C Within the 3. Light 75 mm 3 in. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

As an alternate method, the thickness may be measured using two bars with? Scattered areas of non-uniform surface and scattered surface blemishes are permissible. A number in parentheses indicates the year of last reapproval. Type I which is a transparent flat glass and Type II which is a patterned and wired c11036 glass. For nonlinear dimensions of nonrectangular shapes, tolerances shall be as agreed upon by the involved parties.


Allowed with a minimum separation of mm 48 in. Users of c11036 standard are expressly advised that determination of the validity of any such patent rights, and the risk of infringement of such rights, are entirely their own responsibility. Start with the glass sample parallel with the zebra board identi?

C — 06 Standard Speci? Opening in the mesh shall not exceed 16 mm 5? Type II glass shall have clear and tinted classes while Type I glass shall only have the clear class. The monolithic flat glass shall be supplied as cut sizes or stock sheets. A None allowed None allowed None allowed See 6.

Discoloration and slight distortion of wire are permissible. Allowable blemishes per Table 3 PLUS three rejectable point blemishes Production of architectural glass products including coated, heat treated, laminated, and other select glass products.

This ashm is subject to revision at any time by the responsible technical committee and must be reviewed every? Rotate the specimen clockwise from zero until it reaches the angle at which the distortion appears and report that angle as the vision interference angle. Table 9 does not apply to glass thicker than The viewer shall move towards the specimen until a blemish is detected if any.

The allowable blemish sizes listed in Table 3 include associated distortion for Q1 and Q2, but Q3 and Q4 do not include associated distortion. Typical minimum thickness for DST is c0136. Glass intended to be used primarily for architectural glazing products including: This glass is intended to be used primarily for architectural glazing products including: NOTE 3—Edges may be supplied or speci?


Flat Glass Inspection Criteria per ASTM C 1036 – 11/ASTM C 1048-12

E Provided that normally nondetectable blemishes do not form a cluster that is detectable at mm 6 ft. This standard has been approved for use by agencies of the Department of Defense. None allowed None allowed None allowed None allowed Allowed Allowed with a minimum separation of mm 24 in.

Glass Standards and Guidelines. The following chart lists the industry standards and specifications that apply to glass used in windows, doors, skylights and architectural glazing applications. Specifies the quality requirements for flat laminated glass consisting of two or more layers of glass bonded with an interlayer material. The values given in parentheses are for information only. Production of general use mirrors and other applications. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application.

Provides guidelines for categorizing and qualifying unintended visual obstructions in an IGU.