CISCO EIGRP COMMAND AND CONFIGURATION HANDBOOK PDF

INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE . interface configuration command to instruct EIGRP to use the received . Therefore, to connect disparate EIGRP sites, you must configure the neighbor command with LISP encapsulation on every CE in the network. Cisco Nexus Series NX-OS Unicast Routing Configuration Guide, .. The { ip | ipv6} passive-interface eigrp command suppresses neighbors from forming.

Author: Kegis Kasida
Country: Somalia
Language: English (Spanish)
Genre: Love
Published (Last): 22 January 2014
Pages: 101
PDF File Size: 15.23 Mb
ePub File Size: 19.99 Mb
ISBN: 242-1-74673-310-3
Downloads: 88630
Price: Free* [*Free Regsitration Required]
Uploader: Kazrataur

EIGRP Configuration| Step By Step Guide

Austin config-keychain-key key-string tower Identifies the key string. About Affiliates Cisco Systems, Inc. Houston config-router key chain eddie Identifies a key chain name, which must match the name configured in interface configuration mode. The verification and troubleshooting examples in this section will all use the topology shown earlier, composed of routers R1, R2, R3 and R4. Austin config-keychain-key key-string tower.

But we have included the explicit no shutdown command in router configuration mode to make sure EIGRPv6 works even if you happen to use an older IOS version to practice the example.

EIGRP Configuration| Step By Step Guide

The FS feasible successor is a route that meets the feasibility condition and can potentially become the successor route if the successor route fails. The first step in Csico verification would be to make sure it is enabled on all the right interfaces. Houston config-keychain-key accept-lifetime Houston config-keychain-key key-string tower Identifies the key string.

The remote subnet As a result, the rest of the routers in the topology will not be aware of the subnet and will not be able to route packets to the subnet. Instructs the router to include routes with a metric less than or equal to n times the minimum metric route for that destination, where n is the number specified by the variance command.

  HORIA VARLAN CARTE DE BUCATE PDF

EIGRP Configuration With Packet Tracer ⋆

Austin config-if ip address Sample Chapter is provided courtesy of Cisco Press. For instance, you could have two routers advertise the same network— Creates an incoming global distribute list that refers to access control list ACL 1.

Advertises directly connected networks classful address only. Austin config-router no auto-summary. The configuration settings are made with the maximum-paths and variance commands in EIGRPv6 router configuration mode, reached with the ipv6 router eigrp command.

HULL config-router distribute-list 30 out eigrp Router config-router passive-interface default Prevents the sending of hello packets out all interfaces. If the parameters do match, the two routers become neighbors and each router adds the other to its EIGRPv6 neighbor table, as listed with the show ipv6 eigrp neighbors command. Ane IPv6 routing table of R1 displayed above has several subnets, but two of them are highlighted.

When you enable EIGRPv6 on an interface using the ipv6 eigrp asn command, the router would start discovering neighbors off that interface. With the maximum-paths router configuration command, up to 32 equal-cost entries can anv in the routing table for the same destination. One incoming global distribute list One outgoing global distribute list One incoming interface distribute list One outgoing interface distribute list One outgoing redistribution distribute list.

  ASTM B88M PDF

Houston configure terminal Moves jandbook global configuration mode.

There are lot more similarities than differences, so it makes sense to list the few differences that exist between the two protocols. Sample Chapter is provided courtesy of Cisco Press.

Recommended practice is that you turn off automatic summarization if necessary, use the ip summary-address command, and summarize manually what you need to.

It can be applied to external type 2 and external type 1 routes but not to intra-area and interarea routes. The rest of the configuration simply enables EIGRPv6 on all interfaces an the ASN to associate with the interface, using the ipv6 eigrp asn command.

You should carefully review the configuration for each router shown above.

Houston config-keychain-key exit Returns to global configuration mode. Identifies a key chain name, which must match the name configured commane interface configuration mode. Once two EIGRPv6 routers become neighbors, they should exchange all appropriate network topology information. You can use the show ipv6 protocols command to list all EIGRPv6-enabled interfaces including passive interfaces.

See All Related Articles. As a result, networks Creates a standard ACL number 20 and explicitly denies the cofiguration R4 configure terminal Enter configuration commands, one per line.

EIGRP configuration

Router config-router distribute-list 1 in. Houston config-router key chain eddie. HULL config access-list 10 deny