FLUKE 5500A MANUAL PDF

Each Fluke product is warranted to be free from defects in material and The A Manual Set provides complete information for operators and service or. Warning If the A Calibrator is operated in any way not specified by the A Operators Manual or other documentation provided by Fluke, protection. View and Download FLUKE A operator’s manual online. Multi-Product Calibrator. A Test Equipment pdf manual download.

Author: Fekora Shadal
Country: Niger
Language: English (Spanish)
Genre: Technology
Published (Last): 8 November 2005
Pages: 492
PDF File Size: 11.84 Mb
ePub File Size: 20.13 Mb
ISBN: 189-9-81999-754-8
Downloads: 76558
Price: Free* [*Free Regsitration Required]
Uploader: Akinos

Fluke Calculator A/COIL User Guide |

At 5 s the uncertainty is 5, ppm; At 50 ps the uncertainty is Equipment Setup for High Frequency Flatness. Follow these steps tluke calibrate low frequency Leveled Sine Wave flatness for the amplitude being calibrated: If there are faults associated only with capacitance measurement, the A50 board most likely needs replacement.

Remove the top cover. This custom control icon provides complete serial communications capabilities for this program. Refer to Figure for the proper setup connections. Page DC voltage references developed for the 5500x. Then follow these steps to calibrate edge amplitude: Page Select COM as required.

If you make an entry error, press to clear the display, then reenter.

A Operator Manual

The supplies are fused on the motherboard. Where To Go from Here Parts price information is available from manuql Fluke Corporation or its representatives.

  GENTE TOXICA BERNARDO STAMATEAS DESCARGAR PDF

AC Voltage into a 1 M Load cont. Enter the desired voltage. Calculating Power Uncertainty Overall uncertainty for power output in watts or VARs is based on the root sum square rss of the individual uncertainties in percent for the selected voltage, current, and power factor parameters: Connections for Calibrating TC Measure 1.

General Specifications The A specifications include stability, temperature coefficient, linearity, line and load regulation, and the traceability of the external standards used for calibration.

For each calibration step, take samples for at least two seconds, using the HP A MATH functions to enter the average or mean value. The blue softkey under Output toggles the impedance between 50 O and 1 MO. The following examples show the first few lines of calibration shifts and calibration constants reports, in both printout and spreadsheet formats.

If it does not, repeat the aberration and rise time adjustments until you achieve the best compromise, within the listed tolerance levels. Voltage Function A Service Manual The locations of the analog flkke are printed on the guard box cover. Chapter 2 Preparing for Operation Contents Page Rs Interface Overview to baud selectableand distances up to 50 feet. Then proceed with the flike sections to verify the AC Voltage function.

Page DDE: Connections for Calibrating Four-Wire Ohms.

  KDL50W800B MANUAL PDF

Chapter 9 Accessories Title Page Also suspect is U31 on the A6 assembly. Some commands require a previous condition be set before the command will be accepted by the A Calibrator. Fluje the Leveled Sine Wave Balance. Repeat steps 4 and 5 for all of frequencies listed in Table Remove the eight Phillips screws from the top cover.

Fluke 5500a – Sc300 Multi-product Calibrator

Remove the three Phillips screws that are accessible through holes in the bottom flange. High Frequency Flatness Verification at 70 mV.

The dimensional outline for the A Calibrator is shown in Figure For example, if testing a K thermocouple, the cable and miniconnector are for a K thermocouple. A manuxl appears in the Output Display under the lowest digit and begins changing that digit.

Fluke 5500A/COIL Calculator User Manual

General specifications that apply to the A Calibrator can be found in Chapter 1. Set the oscilloscope to display the leading edge and the first 10 ns of the edge signal.

Verification Tables The 500a test points are provided here as a guide when verification to one-year specifications is desired.