ISO 2846-1 PDF

Partie 1: Impression lithographique offset sur feuilles et à bobines. STANDARD. ISO. Third edition. Reference number. ISO (E). ISO is an international standard used to determine color and transparency conformance of four- color lithographic printing inks. determining if “High Tack Bengal Process Series” inks conformed to ISO ISO – was performed using an IGT Printability Tester. The four inks were.

Author: Arakora Akinoshura
Country: Tunisia
Language: English (Spanish)
Genre: Life
Published (Last): 28 June 2015
Pages: 108
PDF File Size: 2.54 Mb
ePub File Size: 9.95 Mb
ISBN: 196-6-46972-542-6
Downloads: 21163
Price: Free* [*Free Regsitration Required]
Uploader: Mulabar

This also applies as the standard for sheet-fed offset. That means that the difference between printed and blank black increases. Input values and average ISO value for cyan transparency.

Transparency As process printing inks have to show sufficient transparency for the functioning of multi colour printing, corresponding values have been stipulated in ISO286-1 may not lso undercut. The reciprocal value of the inclination of the line of ios fit by the measuring points, describes the extent of transparency. The revision for offset printing is complete with the present standard ISO The colours cyan, magenta and yellow also correspond to this standard.

However as actual application is affected by many factors over which we have no control, we are not liable for printing failures. The usage of defined process printing inks with fixed properties in terms of colour is one of the most important preconditions to achieve reproducible print results.

For the evaluation of the transparency, several printing samples with graduating ink film thicknesses are to be printed on black substrate.

ISO Epple Druckfarben AG

Print products should be produced and also reproduced, ixo and again, all over the world, with the same results. It was very difficult to define the colorimetric nominal values which are to be jso future chromaticity coordinates of the standardized printing inks, as values had to be found that were acceptable to all experts from the various economic areas. The colour values determined in the standard are a further approach to standardise offset printing. This technical iiso sheet is designed for your information and reference.

  HIDROKARBON ZEHIRLENMELERI PDF

These series are produced by us with utmost care and are delivered with the lowest colour 286-1 fluctuations. At complete transparency sometimes to be found with cyana horizontal line shows. This colour definition was stipulated in standard DIN 16 There are some colour systems on the market which work with up to seven colours in order to display the widest possible colour space.

Compliance with the standard is given if the measured values do not exceed the stipulated value of transparency. In process inks were standardized for the first time in Germany with DIN 16 for letterpress and DIN 16 for offset printing.

ISO 2846 Conformance Tested Ink & Suppliers

The inclination is then 0. According to our measurements, the most common ink series, especially ours, are at least very close to the nominal value and mostly within the given tolerances. The term for this new series was European isoo scale or sometimes shortened to European scale. Measurement geometry Standard illuminant: In case a printing ink is not totally transparent, the light that touches the print sample during observation or colour measurement is increasingly scattered according to higher ink film thickness.

ISO 2846-1

In practice, however, this means that when launching colour management, the already used ink series in the print shop should serve as reference considering the commonly used full tone densities in the print shop.

Input values and average ISO value for yellow. In general, the number of primary colours is optional; for economic reasons, however, not too many primary colours should be used.

The four-colour system has established itself in the main printing procedures, however. Europe For Europe, the average values of more than 60 current process inks from different producers were generated. If the colour distance between printed and blank black is put down as function of the ink film thickness, a line arises whose inclination is low at a high transparency of the printing ink and higher if the transparency is lower.

  ALIMENTACION YOGUICA PDF

In complete accordance with the European colour scale, the international standard ISO was published in Input values and average ISO value for magenta. Information on standard ISO For multi-colour printing the inks are mixed by printing primary colours over or next to each other in solid and screen areas.

Colour values It was very difficult to define the colorimetric nominal values which are to be the future chromaticity coordinates of the standardized printing inks, as values had to be found that were acceptable to all experts from the various economic areas. It is based on and conforms to our current knowledge. As process printing inks have to show sufficient transparency for the functioning of multi colour printing, corresponding values have been stipulated in ISOwhich may not be undercut.

For Europe, the average values of more than 60 current process inks from different producers were generated. In order to achieve better fastness properties, for example alkali or light fastness, a group of experts from the CEPE European Council of producers and importers of paints, printing inks and artists colours recommended the standardization of a new ink series, in Colour values for black were also included in the new standard.

For multi-colour printing the inks are mixed by printing primary colours over or next to each other in solid and screen areas.

Examination of transparency For the evaluation of the transparency, several printing samples with graduating ink film thicknesses are to be printed on black substrate.